Arri L7-C LED Fresnel
E-CODE: 13201
- LE2: 25% Brighter than previous L7-C
- Beam Angle: 15 – 50 Degrees
- 7″ Fresnel Lens
- 2800 – 10,000K, Continuously Variable
- Full RGB+W Color Gamut
- Runs with or without Fan
- DMX Control, On-Board Control
- Low Electrical Draw: 160W
Product Details
The Silver/Blue, Manual Mount L7-C LE2 Color LED Fresnel is part of ARRI’s continuing effort to replace traditional Fresnels with powerful LED versions that offer unprecedented color control. The L7-C LE2 shares many characteristics with its predecessor, but the most obvious improvement is a 25% boost in power, increasing the light’s tungsten equivalency from 750W to 1000W. This stand/manual mount version has a yoke with a 1-1/8″ Junior pin.
The key characteristic of any Fresnel is flood-to-spot capability, and the L7-C LE2 meets and exceeds expectations with an impressive beam angle of 15-50°. There’s no learning curve when swapping out L7-C LE2 fixtures for fixtures with standard Fresnels. In fact, you’re not going to be moving them around or juggling scrims in high places thanks to the 100 – 0% on-board dimming.
The L7-C LE2 is a “fully tune-able” white light source too, allowing you to match existing fixtures from a warm 2800K to ice-blue 10,000K. The on-board controller allows manual intensity control as well as color temperature and +/- green. Specific color shades and skin tones can be matched through the full gamut color mixing feature. All functions can be controlled via DMX, an ideal feature for broadcast studios. The hybrid cooling system allows for cooling both actively (with a fan) or passively (without a fan) for times when the set needs to be dead quiet. The L7-C LE2’s 1000W equivalent output draws only 160W during normal operation, making possible a savings of a 75% over similar output tungsten lights. And low heat means lower AC bills in the studio. You can actually run 9x L7-C LE2’s from a 20A, 120VAC outlet as opposed to two 1000W or three 650W standard fixtures. The L7-C requires a separately-purchased power cable.
The Silver/Blue, Manual Mount L7-C LE2 Color LED Fresnel is part of ARRI’s continuing effort to replace traditional Fresnels with powerful LED versions that offer unprecedented color control. The L7-C LE2 shares many characteristics with its predecessor, but the most obvious improvement is a 25% boost in power, increasing the light’s tungsten equivalency from 750W to 1000W. This stand/manual mount version has a yoke with a 1-1/8″ Junior pin.
The key characteristic of any Fresnel is flood-to-spot capability, and the L7-C LE2 meets and exceeds expectations with an impressive beam angle of 15-50°. There’s no learning curve when swapping out L7-C LE2 fixtures for fixtures with standard Fresnels. In fact, you’re not going to be moving them around or juggling scrims in high places thanks to the 100 – 0% on-board dimming.
The L7-C LE2 is a “fully tune-able” white light source too, allowing you to match existing fixtures from a warm 2800K to ice-blue 10,000K. The on-board controller allows manual intensity control as well as color temperature and +/- green. Specific color shades and skin tones can be matched through the full gamut color mixing feature. All functions can be controlled via DMX, an ideal feature for broadcast studios. The hybrid cooling system allows for cooling both actively (with a fan) or passively (without a fan) for times when the set needs to be dead quiet. The L7-C LE2’s 1000W equivalent output draws only 160W during normal operation, making possible a savings of a 75% over similar output tungsten lights. And low heat means lower AC bills in the studio. You can actually run 9x L7-C LE2’s from a 20A, 120VAC outlet as opposed to two 1000W or three 650W standard fixtures. The L7-C requires a separately-purchased power cable.